Module 16/17 work in progress

Multiple Choice

What is the main focus of AS/NZS 5601.2:2013?

• Electrical installations in residential buildings

• LP Gas installations in caravans and boats for non-propulsive purposes

• Water supply systems in commercial buildings

• Fire safety systems in high-rise buildings

Multiple Select

Which of the following are major changes from AS/NZS 5601.2:2010 included in the 2013 edition?

• Clarification of drainage and ventilation requirements for LP Gas cylinder compartments and lockers

• Guidance on increase in ventilation area where mesh is installed

• New warning label for vents

• All of the above

Multiple Choice

Based on the table of contents, which section would you refer to for information on the installation of piping in LP Gas systems?

• Section 2: Performance Based Design, Installation and Other Essential Requirements

• Section 3: Means of Compliance—Cylinders

• Section 5: Means of Compliance—Piping and Fittings

• Section 6: Means of Compliance—Gas Appliances

Multiple Choice

Which types of vehicles or structures are covered under the application of the AS/NZS 5601.2:2013 standard for LP Gas installations?

• Caravans, boats, houseboats, floating restaurants, and catering vehicles

• Passenger cars and motorcycles

• Aircraft and helicopters

• Residential houses only

Multiple Choice

What are some exclusions specified in the AS/NZS 5601.2:2013 standard regarding LP Gas installations?

• Installations covered by statutory requirements, use of LP Gas as automotive fuel, installations in transportable homes, installation of commercial catering equipment

• Installations in caravans and boats

• Installations in fixed residential homes

• Installations in floating restaurants

Multiple Choice

Which of the following best describes a 'room-sealed appliance' as defined in the standard?

• An appliance that operates without a flue

• An indoor appliance sealed from the room, discharging combustion products outside and taking air from outside

• A cooking appliance installed on a floor

• A device for detecting carbon monoxide

Fill in the Blanks

Multiple Select

Which of the following are types of flue systems described in the document?

• Natural draught flue

• Open flue

• Power flue

• Sealed flue

Multiple Choice

What is the primary function of a flame safeguard system in gas appliances?

• To detect gas leaks and shut off the gas supply in case of flame failure

• To regulate the pressure of gas entering the appliance

• To remove combustion products from the appliance

• To provide ventilation for the appliance

Multiple Choice

What is the primary purpose of verifying the LP Gas type and pressure before commencing an installation?

• To ensure the gas is suitable and safe for the appliances and pipe fittings to be installed

• To check the color of the gas

• To determine the age of the gas installation

• To ensure the gas installation is aesthetically pleasing

Fill in the Blanks

Multiple Select

Which of the following are acceptable substances for testing gas installations?

• Air

• The gas for which the system is designed

• Oxygen

• Inert gas

Multiple Choice

What are the key requirements for the design and construction of cylinder compartments and gas lockers?

• Adequate size, safe removal and reconnection, sufficient ventilation, and corrosion resistance

• Only adequate size is required

• Only ventilation is required

• Only corrosion resistance is required

Multiple Choice

What fittings cant be used in 5601:2

• Flared fittings

• Crimped fittings

• Long screw connectors

• Shark bite

Multiple Select

What materials cant be used for pipework in 5601:2 on caravans

• Pex

• annealed copper

• Half hard copper

• stainless steel

Multiple Choice

What is the preferred material be used on pipework that pentrates through partitions, or bulk heads?

• Silicone

• Loctite

• Rubber Grommets

• Insulation

Multiple Choice

How far away does gas pipe have to be from a electrical service?

• 25mm

• 10mm

• 50mm

• 100mm

Multiple Choice

What must the pipework be protected from?

• Damage

• Vibration

• Air

• Disimilar materials

Multiple Choice

Pipe supports should be installed with in ...... of every bend,elbow,tee,and branch fitting. Excluding loops.

• 50mm

• 150mm

• 100mm

• 200mm

Multiple Choice

What pressure should we use for a pipework test on caravans and boats?

• 10 KPA

• 14 KPA

• 7 KPA

• 2.75 KPA