Font size
WorksheetsInfiniti (Electrical)
Total questions: 25
Worksheet time: 38mins
What are the major functions of C3P?
Data Monitor
Simulation Test
Active Test
Work Support
What are the suitable signals for checking the Idle condition in
“Data Monitor Mode" in C3P?
ENG SPEED
IGN TIMING
BRAKE SW2
VHCL SPEED SE
What is the major purpose of “Work Support Mode”?
Reducing the parts replacement
Increasing service labor
Improving skills for service staff
Reducing the associated works for component and system adjustments
What is the function of “Active Test Mode”?
Reprograming the ECU program
Temporally changing the ECU specifications
Reducing time for idle condition setting
Temporally changing the ECU control parameter intentionally
What is the purpose of “Oscilloscope Mode” function?
Diagnosing malfunctions of ECU
Setting idle conditions
Measuring signal waves
Reprograming the data of ECU
How many communication lines are there in the CAN system?
One communication line: CAN Low Speed
Two communication lines:
CAN High speed and CAN Low speed
One communication line: CAN High Speed
One communication line:
CAN High speed and CAN Low speed
When is the charge warning light on?
When the ignition switch is set to ON or START
Only when the ignition switch is not set to ON
When the alternator is providing sufficient voltage with engine running
When the alternator is not providing sufficient voltage with engine running
What is the data transmission mode for CAN system?
On a multiple electrical cable for all component concerned.
On a single electrical cable for each component concerned.
On a differential wired pair that consists of one communication line.
On a differential wired pair that consists of two communication lines.
Which is not a type of door lock/unlock systems?
Conventional key
Remote keyless entry
Intelligent key
Voice control
When a foreign object is pinched, how will the power window control system react?
The window continues going up.
The window stops.
The window goes down around 150mm.
The window goes down to the end.
After the battery is disconnected for long time, which operation must you perform on the power windows?
Conformity check
Check the electric window controls
Program the doors
Program the electric windows
In the exterior lighting system, what is the function of the automatic aiming control of the headlights?
Allows the automatic lighting of the headlights.
Allows the automatic shutdown of the headlights.
Allows the headlights to automatically adjust the level of the headlight beam.
Allows automatic switching from low beam to high beam and inversely
Which of the following components control the automatic headlight level system?
AVM
BCM
ECM
IPDM E/R
What is the state of the refrigerant fluid when it leaves the compressor?
Liquid and very hot.
Gaseous and cold.
Gaseous and very hot.
Liquid and cold.
What is special about the oil used in the AC system?
The oil dissolves moisture.
The oil solidifies at high temperature.
The oil quickly absorbs moisture.
The oil can be mixed with other oils.
When diagnosing AC system by touch, which component is hot on input and very cold on output?
Compressor.
Evaporator.
Expansion valve.
Condenser.
What is the first stage of maintenance using the AC recovery machine?
Recovering the refrigerant fluid and the oil.
Evacuation.
Oil measurement.
Adding 200 grams of refrigerant fluid.
Which action must be taken between the AC gas recovering and refilling?
No action is required.
Pressurising the system.
Checking the liquid tank filter.
Performing the process of evacuation.
Which element allows the air coming from the cold loop and the hot loop to be mixed?
The gear motor/actuator and the mixing flap.
The gear motor/actuator and the ventilation flap.
The gear motor/actuator and the distribution flap.
The gear motor/actuator and the recycling flap.
What is the role of the load limiter integrated into the seatbelt?
Protect the head.
Protect the chest.
Protect the neck.
To enable submarining
Which of the following description of the Autonomous Drive Level 2 is true?
Driver can’t not take action of the vehicle until the Autonomous Drive Level 2 is turned off.
It activates only when there is a vehicle in front.
It detects when hands are out off the steering wheel.
It needs only central marked line to be engaged.
What type of traffic sign can be detected by the Traffic Sign Recognition system?
Speed limit sign
No parking sign
No turning right sign
Road direction sign
In which condition will the Blind Spot Warning system alert the driver with indicator and chime?
Another vehicle approaching from behind
Overtaking another vehicle at the next lane
Another vehicle entering from the next lane
Vehicle behind applying brake
Select the correct description(s) concerning the Lane Departure Warning and Lane Departure Prevention:
LDW alerts the driver in situations where the vehicle is straying out of its lane.
LDW alerts the driver in situations when a vehicle is entering in the vehicle lane.
LDP corrects the vehicle's trajectory before a lane is crossed.
LDW uses two radar sensors on the front bumper to detect the lane markers.
In which situation the Forward Emergency Braking help the driver to detect risk of collision ?
Vehicle ahead in the same travelling lane
Vehicle ahead in the next travelling lane
Pedestrian
