Plumbing systems for which a permit is required by this code shall be inspected by the

The Authority Having Jurisdiction shall be notified that work is ready for inspection not less than____ hours before the work is to be inspected.

If a court finds a portion of the code unconstitutional

Temporary connection of the plumbing equipment to the source of energy or fuel for the purpose of testing

A room equipped with a shower or bathtub is a

That part of the lowest piping of a drainage system that receives the discharge from soil, waste, and other drainage pipes inside the walls of the building and conveys it to a point 2 feet outside the building wall is a

The combination of fittings that may be used to make an offset and is considered a vertical pipe are

The part of the horizontal piping of a drainage system that begins_______ feet downstream from the last mobile home site, and conveys it to a public sewer is called a mobile home park sewer.

The pipe or duct that connects a fuel-gas-burning water heater to a vent or chimney is a

The pipe from the source of supply to a building or structure is the

A physical separation that may be a low inlet into the indirect waste receptor from the fixtures, appliances, or devices indirectly connected is the definition for an

Disposal of sewage, or other liquid wastes, shall be by means of

A connection to the public sewer, or private sewage disposal system, is required for

Except as otherwise provided in this code, no plumbing system, drainage system, building sewer, private

sewage disposal system, or parts thereof, shall be located in

The building drain from the front building may be extended to the rear building when both buildings are

located and no private sewer is available or can be constructed

Cast-iron soil pipe, installed vertically, shall be supported at its base and

Two-inch copper drain pipe installed horizontally shall be supported at intervals not exceeding

All materials, fixtures, or devices used or entering into the construction of plumbing and drainage systems shall

Section 312.2 prohibits the direct embedment of hubless cast-iron pipe in a concrete slab.

Drain pipes subject to condensation over food storage in food-handling establishments shall be

Test gauges shall not have a pressure range not exceeding

Fixtures having concealed slip-joint connections shall be provided with

The diameter of a waste outlet and fixture tailpiece for a bathtub shall not be less than

Trough urinals shall be

With two noted exceptions, all shower compartments and receptors shall be capable of encompassing a diameter circle.

Drinking fountains shall not be installed in

Shower pan linings may be constructed with

Water closets set side by side shall be no closer than

The minimum distance from a side wall or partition to the center of a urinal shall be_____ inches

The joint of a wall-hung lavatory, where it is in contact with the wall, shall be

Wall-hung lavatories shall be supported by

The tailpiece diameter for lavatories shall not be less than

Strainers having waterway areas at least equivalent to the area of their tailpiece are required for

Showers and tub-shower combinations shall be provided with individual control valves of the

Maximum hot water temperature discharging from a bidet shall be limited to

Closet bends or stubs shall be cut off so as to present a smooth surface, even with the

A domestic dish washing machine shall discharge indirectly through an air gap fitting into a

Plastic piping used for venting water heaters shall be

It shall be unlawful for any person to install, remove, or replace any water heater without first

Vent connectors of natural draft appliances_________ be connected to mechanical draft systems operating under positive pressure.

A vent connector connected to a chimney flue serving a fireplace is

The minimum capacity for a storage water heater is

A water heater installed in a residential garage shall be

Water heaters of other than the direct-vent type shall be located

A three-bedroom home with two bathrooms is equipped with a gas storage-type water heater. The minimum capacity for the water heater in accordance with the first hour ratings is

Indoor combustion air supplied by using the "Standard Method" requires a minimum volume of

Draft hood-equipped and other fuel-burning Category I water heaters may be installed in closets, bedrooms and bathrooms provided

Where damage may result from a leaking water heater, a watertight pan of corrosion-resistant materials

shall be installed beneath the water heater when it is located in an attic or

A water heater is installed on the roof of a building more than 15 feet in height. The code requires to the roof unless other means acceptable to the Authority Having Jurisdiction are used

In seismic design categories , water heaters shall be anchored or strapped to resist horizontal displacement due to earthquake motion.

Where utilizing louvers and grills to provide combustion air, and the design and free area are not known, it shall be assumed that wood louvers will have percent free area and metal louvers and grills will

have percent free area.

Exit terminals of mechanical draft systems shall not be less than above grade where located adjacent to public walkways.

Clearances for listed water heaters shall be

Where providing combustion air for draft hood-equipped water heaters installed in repair garages, all combustion air shall be obtained from

A Type B gas vent shall terminate at least feet above the highest connected equipment draft hood or flue collar.

A listed water heater, located in an interior floor level closet, must have an access dimension_____for servicing purposes.

For attic installation, the passageway and servicing area adjacent to the appliance shall be

The code requirement for "an adequate supply of potable running water" is for

Ballcocks in water closet tanks shall be installed so that the critical level of the water inlet is above the full opening of the overflow pipe at least____

PEX tubing shall not be installed within the first_____of piping connected to a water heater.

The piping material(s) not approved in the cold water piping located inside a building is_________

Water piping systems shall be designed on the basis of the

After allowing for friction and other pressure losses, the residual water pressure shall be at least

Any water heater connected to a separate storage tank and having valves between the heater and tank

shall be provided with a

Galvanized steel piping installed under a concrete floor slab within a building shall

Cast-iron fittings, up to and including two inches in size, when used in connection with potable water piping, shall be

The available pressure at the water meter is 80 psi. At the highest supply outlet, 36 feet above the water

meter, the pressure would be_____ psi when sizing a water system according to Chapter 6.

Building supplies shall be no smaller than that required for the installation and, in no case, smaller than inch(es).

CPVC water pipe may be used for hot and cold water distribution systems

All backflow devices or assemblies shall be tested by a

Other than systems sized by the use of Table 610.4, the maximum velocity of a cold water system containing copper and copper alloy tube and fittings shall be limited to

The quantity of water required to be supplied to every plumbing fixture shall be represented by

The size and material of irrigation water piping installed outside of any building and separated from the

potable water supply by means of an approved backflow prevention device is

Flaring tools are used to make joints for

Whenever fixtures and/or fixture fittings are installed that require a residual water pressure higher than 15

pounds per square inch

The duration for a water system pressure test shall be for a period of not less than____ minutes

Plastic materials for piping outside underground shall have a blue insulated copper tracer wire or other approved conductor installed adjacent to the piping.

Solder and fluxes used in piping systems conveying potable water are prohibited when the lead content exceeds

________systems shall be clearly identified, have a purple background with uppercase yellow lettering.

The area of coverage of a single fire sprinkler shall not exceed

The maximum fixture unit loading allowed on a 2 inch waste stack is

The maximum trap loading for a 3 inch trap is

The maximum discharge capacity for intermittent flow only, in gallons per minute, for one fixture unit is equal to

The clearance required in front of a 2 inch cleanout shall not be less than

The minimum size discharge pipe from an ejector or pump in a single dwelling unit having a water closet connected thereto is

Except in single-family residences, drainage

stacks 3 stories or more in height serving are considered suds-producing fixtures.

Vertical drainage lines connecting with horizontal drainage lines shall enter through a

The maximum fixture units allowed on a 4-inch horizontal drain with a 1/8 inch per foot slope is

A straight run of building sewer will require cleanouts at intervals not to exceed

ABS and PVC DWV piping may be installed in structures of

Threads in drainage fittings shall be tapped to allow for

33. The maximum number of fixture units allowed on a 4-inch building sewer with a slope of 1/8 inch per foot,

as compared to a 4-inch building sewer with a slope of 1/4 inch per foot is

The drainage fixture unit value assigned to a bathtub or combination bath/shower is

The building sewer and water piping may be installed in the same trench (with the proper clearances) if

the building sewer piping is .

A domestic dishwasher, with independent drain, has a drainage fixture unit value of

All indirect waste piping that requires an airgap shall discharge into the building drainage system through

Drains, overflows, or relief pipes from a water distribution system shall discharge to the building drain by

No plumbing fixture that is receiving discharge from indirect waste pipes shall be installed until first

approved by the

A standpipe for a clothes washer shall have a minimum and maximum length of

A domestic dishwashing machine shall be connected to the drainage system by using

Water having a temperature above____shall not be discharged under pressure directly into the drainage system

________shall not be used for chemical or industrial waste that requires pretreatment.

No chemical waste vent shall

Condensate from fuel-burning condensing appliances shall be collected and discharged

If the trap from a sink located in a bar cannot be vented,

Vent pipes protect fixture traps against

The combination of vent pipes that will provide sufficient aggregate cross-sectional vent area for required

a 4-inch house sewer is

A 2-inch vent pipe will serve a total of

Horizontal termination of vents from any openable window, door opening, air intake or vent shaft shall be not less than

Vents terminating in roof areas used for sunbathing shall be extended above the roof at least

Parallel vent stacks are required for drainage stacks that extend above the building drain

The pipe size for the common vent serving lavatories installed back-to-back shall be not less than inch(es).

Increasing vents one pipe size will

The fitting that is required for making the yoke vent intersection with the drainage stack is a

Copper tube shall not be used for

Long mains shall be provided with relief vents at intervals of

Horizontal wet venting

A horizontal wet vent shall be not less than two inches in diameter for dfu or less.

One trap may serve a set of not more than________single compartment sinks

The maximum vertical distance for a tailpiece allowed between a fixture and the trap weir is

The developed length of a 2" trap arm, from the trap weir to the inner edge of the vent shall not exceed_____feet.

Each fixture trap shall have a water seal of

The Authority Having Jurisdiction has mandated grease pretreatment for the following fixtures: four non­ emergency floor drains, two commercial food prep sinks, one service sink with a 3-inch trap, and two dishwashers discharging 20 gallons per minute each. The minimum size gravity grease interceptor in gallons required shall be_____

Horizontal 1/2 inch diameter steel fuel gas piping shall be supported at intervals not exceeding _______ feet.

The approximate number of threads to be cut on a piece of 1-inch metallic fuel gas pipe is_____

Where gas piping is installed underground beneath buildings, the piping shall be one of the following

The approximate demand of a freestanding domestic gas range in Btu's per hour is

Gas line pressure regulators installed in the interior of the building, without vent limiting means, shall be

Of those listed, the test medium for a gas piping pressure test shall be

An accessible gas shutoff valve shall be provided _____ of each gas pressure regulator.

Appliance shutoff valves and convenience outlets shall serve a single appliance and shall be installed within ______ of the appliance it serves.

Which of the following is not part of a rough gas piping inspection?

Leaks in gas piping shall be located

A gas appliance regulator shall not be vented to the

The size of the supply piping outlet for a gas appliance shall not be less than _______

The size of a piping outlet for a mobile home shall be not less than

To obtain the cubic feet per hour of fuel gas required for any gas appliance

Except for CSST, gas piping with a service pressure of 1.58 psi shall be tested at a minimum of ______ psi for no less than ______ minutes.