WorksheetsTampo Training Module A 4
Total questions: 17
Worksheet time: 34mins
Which statement below WRONGLY described about Master Machine for New Toy Development ?
以下哪一项是错误描述新产品研发时所用的 Master Machine （移印主控机） ？
A. Weekly Calibration should be conducted on Master Mc to ensure Dead On Setup Requirement always comply.
每周最少一次效俭 Master Machine 的移印跑位， 以确保图案跑位保留在可接受的范围内。
B. The Fixture Base Indexing Speed must be set as similar as during production run, through out entire graphic development tasks.
在图案研发阶段时，机器的夹具底座运行速度必须设置如同生产时的正常运行速度
C. If Multi-color Mc was used as Master Machine, a fixed Graphic Plate Platform must be used for entire development tasks.
如果 Master Machine 是多色机， 那就只应许选用单一钢板底座来完成全套图案研发工作
D.If Multi-color Mc was used as Master Machine, a fixed Fixture Base must be used for entire development tasks.
如果 Master Machine 是多色机， 那就只应许选用单一夹具底座来完成全套图案研发工作
E.If Multi-color Mc was used as Master Machine, Fixture Base must be kept in stay-put condition all the time.
如果 Master Machine 是多色机， 那夹具底座必须在图案研发过程中，全程保持不动状态。
Which statement below WRONGLY described about Rubber Pad use in Tampo Print ?
以下哪一项是错误描述胶头的使用？
A.Pads of different hardness are commonly use within same machine setup.
不同胶头硬度可以使用在同一台机器上
B. Harder Pad provide Sharp Images
硬胶头给予更清晰的移印效果
C.Softer Pad sacrifice image sharpness.
软胶头会牺牲图案的清晰度
D.Harder Pad need higher press force to make print happen
硬胶头要求更大的下压力度
E.Harder Pad most suitable for Textured surface prints.
硬胶头更适合有纹理的表面
Which statement below correctly described Plate (A) & Plate (B) below ?
以下哪一项是正确描述 Plate (A) & Plate (B) ?
A.Plate (A) is to facilitate correction of distorted artwork on contour surface.
Plate (A) 可用予解决 “胶头变形导致图案移位” 的源头。
B.Plate (B) is to facilitate the selection of most optimum Rubber Shape / Type.
Plate (B) 可用来帮助找寻最适合的胶头形状与 种类。
C. Plate (B) should be used before Plate (A) been used.
先用 Plate (B)， 再用 Plate (A)
D.( A ) ( B ) correct
(A) (B) 正确
E.( A ) ( B ) ( C ) correct
(A) (B) (C) 正确
Which Information of New Toy Development are critical to be duplicated
at upcoming Production run ?
以下哪项新产品研发资讯必须在未来生产线上复制 ?
A. Type of Rubber used.
胶头种类
B Location of rubber mounting.
胶头位置
C. Type of Fixture Adaptor.
夹具种类
D. Servo Parameter of SMED Setting, for Print under category C2 & E3.
伺服马达的行程参数 ( C2 & E3 产品类别 )
E. All above.
以上全部正确
Which Print Requirement stated below Doesn’t suitable for Carousel Machine ?
以下哪项打印要求不适合在转盘机上生产 ?
A.Large Component Toy exceeding 200mm x 200mm dimension size
超过200mm x 200mm尺寸的大型组件玩具。
B. Toy with different index travel required to complete the deco.
需要无固定行程运行来完成打印的胶件/玩具
C. Toy with high quota run.
需高配额运行的玩具。
D. ( A ) ( B ) correct
A和B都正确。
E. ( A ) ( B ) ( C ) correct.
A, B, C皆正确。
Which Print Requirement stated below Best to run on Shuttle Machine ?
下列哪一种打印要求最适合穿梭机?
A. Large Component Toy exceeding 200mm x 200mm dimension size
超过200mm x 200mm尺寸的大型组件玩具。
B Toy with different index travel required to complete the deco.
需要无固定行程运行来完成打印的胶件/玩具
C Small Quota run.
小单量产品
D Print with simple Mechanization attachment to complete the print requirement
可用简单的机械化附件完成印刷要求。
E all above correct
以上选项皆正确。
Which stated NOT represent special advantages available on Shuttle Machine with individual prints ability ?
以下哪项不属于 “独立打印穿梭机” 的特点 ？
A.Print on Large Component Part
大胶件打印
B. For Deco with significant different in print surface depth.
在印刷表面深度上有显著差异的胶件上
C. For High Productivity Operations
用于高生产率操作
Which of below correctly describe situation when formulated thinner too much ?
下列哪项正确描述了当前配制好的稀释剂过多时的情况?
A.Color less opaque.
颜色透光性低。
B.Tackiness developed on ink surface not sufficient to facilitate proper ink transfer.
油墨表面产生的粘性不足，导致无法有效的促进油墨转移。
C.Hairy print happen.
出现拉丝的情况。
D.( A ) ( B ) correct.
A和B 正确
E.( A ) ( B ) ( C ) correct.
A, B, C正确。
Which Type of Offset / Alignment present in Tampo Operations ?
以下哪一个图案移位会出现在移印工程？
A.“Whole Graphic” Offset
整个图案移位
B. “Color-to-Color” Offset
色对色的移位
C. “Position” Offset.
位置的移位
D. “Distortion” Offset
“胶头变形”移位
E. All above correct
以上的选项皆正确
Which are Good Recommendations of ink preparation for production start up…
哪些是在生产准备工作时推荐的油墨配制方式…
A.It’s ok to prepare large amount of inks inside ink cup, as it avoid wasting time in stopping the machine to add ink.
在油杯中准备大量的墨水，可避免停机加墨造成的时间浪费。
B.Ensure Ink cup is well enclosed with right design of ink cup enclosure cap at all times.
确保在任何时候， 都用正确的杯盖来密封存在油杯里的墨水。
C.Prepare amount of ink inside ink cup with top-up plan every 4~5 hrs.
在墨杯中准备够4-5小时使用的墨水量。
D.( A ) ( B ) are good recommendations.
A, B 是好的建议。
E.( B ) ( C ) are good recommendations.
B, C 是好的建议。
Which of below correctly describe the function of Thinner ?
以下哪个选项正确描述了稀释剂的功能？
A.Adjust Ink Viscosity
调整油墨粘度。
B. Ability to adjust drying time when varying the mixed ratio within fast dry thinner & slow dry thinner
可根据快干稀释剂和慢干稀释剂的混合比例来调整所需的干燥时间。
C.Attack substrate surface to facilitate Ink adhesion on substrate.
腐蚀基材表面，以促进油墨粘附在基材上的效率。
D.Thinner can be a mixer of 1 or more solvents.
稀释剂可以是一种或多种不同溶剂的混合物。
E.All above correct
以上选项皆正确。
Which of below dictate Ink Drying rate requirement ?
下列哪项可直接影响 油墨干燥率的需求 ?
A.Depth of Print Stroke.
胶头向下打印的行程 / 深度。
B.Room Humidity
房间的湿度
C.Machine Speed.
机器的运转速度
D.( B ) ( C ) correct.
B，C都正确
E. ( A ) ( B ) ( C ) correct.
A, B, C皆正确
Which items below are calibration kit that work to ensure consistent
artwork distorted pattern between different machine ?
以下哪一项校准套件是用于确保扭曲图案不会发生在不同机器上？
D.( A ) ( C ) correct
A 和C都正确
E.( B ) ( C ) correct
B和C都正确
Which image below correctly describe setup for Plate Making equipment
& Other New Tampo Machines it should be ?
以下哪个图案准确描述制作钢板机器和其它移印机器需有的设置？
E All above correct
以上选项皆正确
Which condition below present during “Distortion” Offset
以下哪种情况会出现在“胶头变形”的图案偏移？
A.Not use same rubber type as during graphic development.
生产时所用的胶头与第一次图案研发时使用的胶头不相同
B. Graphic image registration offset.
图案本身定位偏移
C. Rubber not in same position as during graphic development.
生产时胶头的位置与第一次图案研发时的位置不一样
D.( A ) ( C ) correct.
( A ) ( C ) 都正确
E. ( A ) ( B ) ( C ) correct.
( A ) ( B ) ( C ) 皆正确
Which statement below correctly describe both Plate Making Methods…
以下哪一个说明正确描述钢板的两种制作方法。。。
- Direct to Plate Laser Method &
- Light Box Film Registration Method
直接镭射方法和灯箱定位方法
A.“Direct to Plate Laser Method” give repeatability on image registration between different laser machines
直接镭射方法给予较高的图案定位的重复性
B. Accuracy of image registration is highly human dependent with “Light Box Film Registration Method”
灯箱定位方法的准确性是高度依赖于人力
C. The RISK of “Light Box Film Registration Method” is when the Glass Fixture broken.
Registration reference on Glass Fixture cannot be duplicated with new fabricate glass fixture.
灯箱定位方法的缺点在于当玻璃损坏后，新更换的玻璃无法实现旧的基准点
D.( A ) ( B ) correct.
A和B都正确
E.( A ) ( B ) ( C ) correct.
A, B, C皆正确
Which statement are correct describing the print for “Orange color” Roof Top as highlighted ?
哪一个说明是正确描述“橙色”打印部分？
C. Pin holes defect due to air trap is a common defect for this graphic, if rubber shape was not chose correctly
如果胶头的形状选择不符合，就会导致空气渗透到油墨中而产生针孔缺陷
D.( A ) ( C ) correct
A和C都正确
E.( B ) ( C ) correct
B和C都正确
