NEW
Font size
WorksheetsGear Box
Total questions: 45
Worksheet time: 23mins
These Gears are used in 90 degree applications
Idler Gears
Bevel Gears
Spun Gears
Jack Gears
Gear used in most passenger vehicle steering applications
Jack Shaft Gear
Worm Gear
Rack and Pinion
Bevel Gear
What gear is used to make the output shaft reverse direction?
Driver Gear
Worm gear
Helical Gear
Idler Gear
Driver Gear has 30 teeth. Driven Gear has 15 teeth. What is the Gear Ratio?
3 : 2
2 : 1
1 : 3
1 : 2
What is the name of the pointed part in this torque converter illustration?
Clutch
Impeller
Stator
Planetary gear
Identify the type of gear
Spur Gear
Helical Gear
Worm Gear
Rack and Pinion
Identify the type of gear
Spur Gear
Bevel Gear
Worm Gear
Rack and Pinion
Identify the type of gear
Spur Gear
Bevel Gear
Worm Gear
Rack and Pinion
Identify the type of gear
Spur Gear
Bevel Gear
Worm Gear
Rack and Pinion
Double Helical Gear
Spiral Bevel Gear
Internal Gear
Spur Gear
Spiral Bevel Gear
Spur Gear
Rack & Pinion Gear
Straight Bevel Gear
Spiral Bevel Gear
Worm Gear
Internal Gear
Straight Bevel Gear
Rotational Gear
Planetary Gear
Rack & Pinion Gear
Multi-Gear
synchronous mesh gear box is used in which vehicle
6-wheelers
4-wheelers
2-wheelers
3-wheelers
The coefficient of friction for the clutch facing is approximately
0.1
0.4
0.8
0.2
What is illustrated in the image shown?
Reverse gear idler
Gearbox interlock device
Synchromesh selection unit
Differential drive unit
Which one of the following should be used to finally tighten flywheel bolts?
An air wrench
An impact wrench
A torque wrench
A rachet wrench
What is the most accurate equipment to check the flywheel face for warping prior to replacing a clutch?
Micrometer
vernier caliper
dial test indicator
feeler gauge and straight edge
What type of final drive crown wheel gear is shown in the image?
Spur
Helical
Hypoid
Planet
What component holds the selected gear in mesh?
Synchromesh hub
Detent mechanism
Selector fork
Interlock mechanism
which one of the following applies to a clutch opearating cylinder ?
it is sealed and never needs its fluid checking
it is attached to the clutch release bearing
it is attached to the clutch release bearing
it used air as operating medium
What is the main type of gear used in a constant mesh gearbox?
Bevel
Helical
Hypoid
Spur
What is the function of a gearbox baulk ring?
Hold the gear selector in position
Assist gear change speed synchronisation
Maintain gear oil to the bearings
Act as a reverse gear idler
What type of transmission will a front wheel drive vehicle use?
Rear axle
Hypoid axle
Dead axle
Transaxle
How many forward gears would the gearbox shown in the image have?
3
4
5
6
What is used to check flywheel run out?
Micrometer
Set square
Vernier caliper
Dial test indicator
Which one of the following is a routine service task carried out on a hydraulically operated clutch mechanism?
Adjusting the slave cylinder position
Replacing the master cylinder seals
Checking the fluid level in the reservoir
Checking the condition of the flywheel face
What is one function of a clutch?
Prevent two gears being selected at the same time
Allow the driver to overrun the vehicle when travelling downhill
Provide a means of increasing engine power as engine speed increase
Control the torque transmitted from the engine to the engine to the transmission system
What is the main type of gear used in a synchromesh gearbox?
Hypoid
Spur
Conical
Helical
What is used to lock the tpe of nut shown in the image when it is used on a stub axle
Nylon insert
Split pin
Locking wire
Lock plate
What are the main items in the image shown?
Hookes type joint layrub coupling and rubber boots
Constant velocity joint ,plunge joint and rubber boots
Constant velocity,bellows and propeller shaft
Hookes type joint ,propeller shaft and latex gaiters
what does the image from a workshop manual show?
Positioning of spring circlips in a synchromesh hub
Positioning of locking plates in a synchromesh outer sleeve
Method of locating a pinion to the gearbox mainshaft
Method of fitting the cluster gear to the layshaft
