When inspecting the parking brake, make sure there is no _____ creep.

A technician is testing a motorized RV. The first step enacted is ensuring that the seat moves up, down, forward, and back. Identify the next main steps for the technician to perform.

The engine must run for a few minutes for this to work properly.

When performing PDI on chassis dash components, check rear and side view

When performing PDI on chassis dash components, check

AS a typical part of PDI, a technician needs to ensure headlights function when

Which is a convenience light?

What should be warm to be properly checked?

When inspecting the hydraulic fluid level in the reservoir, clean the top of the reservoir before removing the cap to

For chassis leveling systems, hydraulic fluid should always be checked when levelers and/or rooms are

When interpreting the year of production, an RV tire has a typical life of

When verifying the age of a tire, "1206" in the last grouping indicates the tire was made in the

When inspecting tires on a towable RV, inspect lug nuts for proper

When verifying the installation of pin box couplers on the 5th wheel hitch, the hitch should be _____ the frame.

Inspect the whole underside of the towable coach looking for loose, hanging, or _____ components.

Before using stabilizer jacks, be sure that the landing gear on the _____ wheel operates properly.

When inspecting stabilizer jacks, ensure they fully extend and

Where do the trailer brakes get their power when the brake-away switch is activated?

When testing electrical brakes, a technician pulls the breakaway cable while spinning the wheel. If the breakaway is properly functioning,

Verify that the level sensor, if so equipped, is synchronized with the _____ of the coach.

A technician is verifying the operation of slide-out and seals. Which of these is needed during this process?

Tongue weight (TW) involves _____ force.

Gross Axle Weight (GAW) is the actual weight of a fully loaded vehicle carried by _____ axle(s).

A technician is weighing a vehicle with no cargo as built in the factory. The vehicle includes full fuel, engine oil, and coolants and no freshwater, propane, occupants, or dealer-installed accessories. Which type of weight is the technician measuring?

GCWR - GVWR (trailer) =

GCWR is most closely associated with

CCC is equal to weight minus a couple factors. What is one of those factors?

CCC was formerly called

CCC stands for _____ Carrying Capacity.

The GVWR minus UVW, full fresh water, full propane, and SCWR is equal to?

Consult the vehicle manufacturer, tire dealer, or tire manufacturer when considering changing to a tire other than those shown in the

Canadian Compliance Labels are

If a vehicle does not have a certification label listed on it, find tire and loading information

When checking that the RV is equipped with all seatbelts required, ensure that each seating location in the motorhome has a seat belt or is

When making interior adjustments and cleaning up, make sure all seats are

When inspecting satellite dishes, verify they are mounted securely and that

When inspecting interior electrical components

When performing an interior electrical inspection, verify the _____ volt DC ports have power.

When in the motor home cockpit, test steering wheel adjustment and check that it is

When testing steering wheel adjustment, check for _____ when it is not turned to either side.

When performing PDI on the entrance and compartment doors, the technician should have keys to fit every lock. This means that _____ set(s) of keys should exist.

Inspect all entrance doors and drip caps for

When performing PDI on the entrance and compartment doors, test operation of all compartment doors and _____ as necessary.

When checking entrance doorsteps, _____ them if needed.

If a roof is not walk-on style and a technician must walk on it

There are five types of roofing material used on RVs. They are aluminum, fiberglass, PVC, TPO, and

Ensure that _____ decals are on the unit.

When performing a check of the exterior, look for cracks or holes in the

RVs are required to have a minimum of _____ exits located remote from each other.

Ensure exits operate with no more than _____ pounds of force required to open them.

What is shown in the picture?

A folding camper has

When performing PDI with a lift mechanism, make sure that all _____ corners are raised the same amount.

When performing PDI on a folding camping trailer, raise the roof

What is shown?

At maximum, truck campers can sleep _____ people.

Which of the following should be attached to the camper body?

The piece of equipment that runs between the pickup and camper is called the

A technician must verify which weight capacity of a truck to use a truck camper?

Verify which of the following weights regarding the adequacy of the pickup?

When performing PDI on expandable rooms, slideout operation can be hindered by

When performing PDI on slide outs, verify alignments in open and closed positions

Primary and secondary are two major types of

When checking seals that are already in an RV, a technician must