Worksheets9189 Electrical Powerpoint 1
Total questions: 55
Worksheet time: 28mins
What is the primary difference between plumbers and electricians according to the text?
Plumbers are also trained as electricians.
Plumbers are not electricians but are involved with electrical appliances.
Plumbers do not need to know anything about electrical appliances.
Plumbers and electricians have the same training.
Why do plumbers need to have a working knowledge of electrical appliances?
To install new electrical systems.
To diagnose basic faults in electrical appliances.
To replace electricians.
To design electrical circuits.
Which of the following is NOT listed as an example of electrical procedures a plumber may perform?
Thermostats
Pumps
Wiring new houses
Boiler controls
Which of the following is an example of an electrical procedure that a plumber may perform?
Installing new electrical outlets
Earth bonding
Rewiring a building
Installing solar panels
Under the Approved Document Part P regulation, who is not required to be Part P qualified to replace a like-for-like component?
A fully qualified electrician
A plumber
A person proven competent in the understanding of the Building Regulations Part P
A building inspector
What is the exception to the rule that a plumber does not need to be Part P qualified to replace a like-for-like component?
When the installation is in a danger zone
When the installation is in a kitchen
When the installation is in a living room
When the installation is in a bedroom
Who must undertake the work if an installation is located in a danger zone?
A plumber
A fully qualified electrician or a person proven competent in the understanding of the Building Regulations Part P
A building inspector
A homeowner
Which of the following is considered a danger zone under the Building Regulations Part P?
A room containing a kitchen sink
A room containing a bath or shower
A room containing a washing machine
A room containing a refrigerator
Where can you find the link to the Building Regulations Part P document?
On the City and Guilds of London Institute website
On the Office of the Deputy Prime Minister website
On the provided URL: https://assets.publishing.service.gov.uk/government/uploads/system/uploads/attachment_data/file/441872/BR_PDF_AD_P_2013.pdf
On the Electrical Safety Council website
According to the Health and Safety at Work Act 1974 (HASAWA), what must you take into account while working?
The cost of the tools and equipment
The safety of those working around you
The time taken to complete the job
The weather conditions
What is essential to do with damaged equipment according to the responsibilities outlined?
Continue using it until it completely breaks
Sell it to a third party
Remove it from service and report it to your employer
Ignore it and keep working
What should you always do with your employer according to the Health and Safety at Work Act 1974 (HASAWA)?
Compete with them
Cooperate with them
Disregard their instructions
Work independently from them
What must you check about the tools and equipment you use?
If they are new
If they are fit for purpose
If they are expensive
If they are popular brands
What do the EAW (Electricity at Work) Regulations cover?
Installation, testing, and maintenance of commercial electrical systems
Design and construction of electrical systems
Manufacturing of electrical equipment
Sales and marketing of electrical products
According to the EAW Regulations, what must be done with damaged equipment?
It should be repaired immediately
It should be taken out of service
It should be sold at a discount
It should be used with caution
What is important for an engineer to do according to the EAW Regulations?
Only perform tasks they are qualified to do or are suitably supervised
Work independently at all times
Perform all tasks regardless of qualification
Supervise other engineers
What do the CDM (Construction Design and Management) Regulations state about the duty of care?
It is the responsibility of the site manager only
It is the responsibility of all to contribute to the health and safety of a construction site
It is the responsibility of the construction workers only
It is the responsibility of the government
What should be in place according to the CDM Regulations to cover all aspects and activities of site work?
A financial plan
A marketing plan
A safety plan
A construction plan
What do the CDM (Construction Design and Management Regulations) state regarding the duty of care on a construction site?
There is no duty of care required.
Only the site manager is responsible for health and safety.
Everyone must contribute to the health and safety of the site.
Only the workers are responsible for their own safety.
What do Building Regulations include standards for?
Only electrical safety.
Electrical safety, fire safety, ventilation, and drainage.
Only fire safety and ventilation.
Only drainage.
Which part of the Building Regulations covers electrical work?
Part L
Part P
Part M
Part N
What should always be followed to ensure the correct installation and operation of electrical equipment?
Building Regulations
CDM Regulations
Manufacturers’ instructions
Safety guidelines
What does BS 7671 cover in terms of electrical installations?
Design, installation, and testing
Manufacturing, distribution, and sales
Marketing, advertising, and sales
Research, development, and innovation
What are the 18th edition IET Wiring Regulations also known as?
BS 7671
BS 7672
BS 7673
BS 7674
In what year did the IEE Wiring Regulations become British Standard BS 7671?
1992
1982
2002
2012
What is the purpose of the on-site guide mentioned in the document?
It contains some information not in BS 7671:2018 and serves as a handy notebook reference for electricians.
It provides marketing strategies for electrical companies.
It includes financial guidelines for electrical installations.
It offers customer service tips for electricians.
What is the purpose of a minor works certificate?
To indicate responsibility for the design, construction, inspection, and testing of the work.
To install a new circuit.
To replace major electrical systems.
To certify the safety of household appliances.
Which of the following tasks should a competent person be able to carry out according to the minor works certificate?
Insulation resistance, earth loop impedance, polarity, and RCD operation.
Installing new electrical circuits.
Replacing household appliances.
Painting and decorating.
What does the signing of the minor works form confirm?
That any minor work carried out does not impair the safety of the existing installation.
That the work is guaranteed for 10 years.
That the work was done by a licensed electrician.
That the work is free of charge.
Who should receive the minor works form?
The person ordering the work.
The local government office.
The nearest electrical supply store.
The insurance company.
Who is qualified to issue a minor works certificate?
Only a Part P qualified operative.
Any homeowner.
Any licensed electrician.
Any construction worker.
What does Part P usually require before electrical work can be carried out on any domestic premises?
Notification of works to the planning department of the local authority
Approval from the homeowner
A signed contract with a registered competent person
A safety inspection by an independent body
When is electrical work considered non-notifiable under Part P?
When it is carried out by a registered competent person or is a minor work
When it is done in a commercial building
When it involves installing a new circuit
When it is inspected by the local authority
Which of the following is an example of minor electrical work?
Installation of a spur outlet for a boiler from an existing ring main
Rewiring an entire house
Installing a new electrical panel
Adding a new circuit to the main breaker
What details should be recorded on the minor electrical works certificate?
Type and rating of the protective supply device or prospective fault current at the supply
The name of the homeowner
The date of the last electrical inspection
The cost of the electrical work
What must be satisfied according to Part P for achieving electrical safety?
All fundamental principles as specified in British Standard 7671:2018
Approval from the local authority
A signed certificate from a registered competent person
A detailed report of the electrical work
Which of the following should be considered when referring to the method statement in a risk assessment?
The color of the equipment
Access to the worksite and others working at the site
The type of food available on site
The number of employees
What should be included in the risk assessment regarding systems and equipment?
The brand of the equipment
The cost of the systems
The integrity of the systems and equipment, as well as working conditions
The color of the systems
What is one of the steps in a typical risk assessment on site?
Walk around the site and identify any hazards, listing them
Count the number of employees
Check the weather forecast
Measure the size of the site
Which of the following should be included in the risk assessment regarding tripping hazards?
The color of the floor
The presence of dust and pollution of the work area with fumes
The type of shoes worn by employees
The height of the ceiling
What should be assessed regarding other contractors in a risk assessment?
Their lunch breaks
Their uniforms
Their operations, live sources, and any COSHH concerns
Their transportation methods
What guideline should be followed in a risk assessment according to the HSE?
The HSE five steps to risk assessment
The HSE ten steps to risk assessment
The HSE three steps to risk assessment
The HSE seven steps to risk assessment
What is the first step in the HSE's five-step guide to completing a risk assessment?
Decide who might be harmed and how.
Identify the hazards.
Evaluate the risks and decide on precautions.
Record your findings and implement them.
According to the HSE's five-step guide, what should you do after identifying the hazards?
Record your findings and implement them.
Review your risk assessment and update, if necessary.
Decide who might be harmed and how.
Evaluate the risks and decide on precautions.
What is the third step in the HSE's five-step guide to completing a risk assessment?
Identify the hazards.
Record your findings and implement them.
Evaluate the risks and decide on precautions.
Review your risk assessment and update, if necessary.
Which step involves recording your findings and implementing them?
Step 2
Step 3
Step 4
Step 5
What is the final step in the HSE's five-step guide to completing a risk assessment?
Identify the hazards.
Decide who might be harmed and how.
Evaluate the risks and decide on precautions.
Review your risk assessment and update, if necessary.
What is the responsibility of an engineer working on site?
To work independently without any cooperation
To recognize the importance of carrying out a risk assessment
To ignore potential hazards
To only follow their own safety protocols
Why is it essential for engineers to cooperate with their employer?
To ensure they get paid on time
To comply with HASAWA
To avoid working with others
To reduce their workload
What should engineers continually reassess on site?
The schedule of their work
The cost of materials
The risks of new potential hazards
The number of workers
What should a plumber's responsibility regarding electrical work not exceed?
Their level of competence
Their level of experience
Their level of education
Their level of confidence
What should you do if you are not confident, capable, or deemed competent to carry out electrical installations or alterations?
Proceed with caution
Do not carry out the work
Ask a friend for help
Refer to a manual
Which of the following can a plumber replace without being Part P registered?
Electrical wiring
Circuit breaker
Like-for-like component such as a shower, pump, fan, or zone valve
Main electrical panel
Who must be Part P qualified?
Anyone who installs a new circuit or alters a significant part of an installation
Anyone who replaces a light bulb
Anyone who installs a new appliance
Anyone who paints a room
What should you do when in doubt about electrical work?
Try to figure it out yourself
Stop and contact an electrician
Look up a tutorial online
Ask a neighbor for advice
