WorksheetsEindexamen Heftruckcertificering
Total questions: 50
Worksheet time: 42mins
What is the main reason for forklift certification?
A. To increase wages
B. To ensure operator safety and compliance
C. To boost productivity
D. To reduce paperwork
Who is responsible for ensuring forklift operators are trained?
A. The government
B. The union
C. The employer
D. The employee
OSHA requires forklift certification to be renewed every 4 years
If a forklift operator is observed operating unsafely, what should happen?
A. Nothing unless there's an accident
B. Immediate termination
C. Retraining and re-evaluation
D. Written warning only
You must wear a seatbelt on a sit-down forklift because It looks professional.
The counterweight on a forklift use to balances the load
The function of the mast is to steer the forklift.
The load backrest extension helps:
A. Prevent loads from falling backward
B. Lift loads faster
C. Reduce wind resistance
D. Avoid overhead hazards
The data plate on a forklift contains:
A. Employee certification
B. Shift schedule
C. Insurance information
D. Maximum load capacity and lift height
A hydraulic system on a forklift is responsible for:
A. Moving the tires
B. Cooling the radiator
C. Starting the engine
D. Raising and tilting the forks
A forklift is rated for 3,000 kg at a 500 mm load center. What is its capacity at a 600 mm load center?
A. 3,600 kg
B. 2,500 kg
C. 2,000 kg
D. 3,000 kg
A load is 1,200 kg and the forklift can lift 1,500 kg. Is this safe to lift?
A. Yes
B. No
C. Only with counterweights
D. Only at full mast
A load is 1.2 m wide and 1.5 m long. What should the fork spacing be?
A. 300 mm
B. 1.1 m
C. As wide as possible without extending outside the load
D. Equal to load width
How much weight can a forklift carry if its capacity is 4,000 kg @ 500 mm and the load center is 800 mm?
A. 2,500 kg
B. 2,800 kg
C. 2,700 kg
D. 3,000 kg
A forklift is on a ramp that rises 1 meter over 10 meters. What is the incline in percentage?
A. 1%
B. 5%
C. 10%
D. 15%
What is the volume of a pallet that measures 1.2 m × 1 m × 1 m?
A. 1.2 m³
B. 2 m³
C. 0.8 m³
D. 3.2 m³
If the mast is tilted back 5°, what is the effect on the center of gravity?
A. It shifts back slightly, improving stability
B. It shifts forward
C. It raises the CG
D. It lowers the load
A pallet weighs 3,200 kg and is 600 mm from the heel of the forks. Capacity is 4,000 kg @ 500 mm. Is this safe?
A. Yes
B. No
C. Only with side shift
D. Only with mast tilted
If your load center increases, what happens to lifting capacity?
A. It increases
B. It decreases
C. It stays the same
D. No effect
A forklift travels 20 meters in 15 seconds. What is its speed?
A. 1.5 m/s
B. 2 m/s
C. 1.33 m/s
D. 2.5 m/s
What’s the weight of 4 pallets each weighing 750 kg?
(use , to mention thousand and . to mention decimal)
(a)
What is the combined weight of a 1.8-ton load and a 2.5-ton forklift?
(a)
How far can a forklift safely lift a 2,000 kg load if rated at 2,500 kg @ 500 mm?
(a)
A ramp has a 12% incline. it is safe for a forklift to go forward with a load uphill.
You must lift 1,000 kg to 4 meters. Your forklift is rated 1,200 kg @ 6.5 meters and it's safe to load.
What is the load center of a 1.2 m pallet, evenly loaded?
(answer in mm)
(a)
Forks are 1,200 mm long. Load center is?
(answer in mm)
(a)
It's safe when you carry a 2,800 kg load at 700 mm load center,
but your capacity is 3,000 kg @ 600 mm.
A forklift needs to lift a 3.5 m³ load of bricks weighing 1,900 kg/m³. What's the total load?
(a)
What is the maximum load capacity of a forklift with a load center of 400 mm if it is rated for 2,500 kg @ 500 mm?
B. 2,200 kg
A. 2,000 kg
C. 2,500 kg
D. 2,800 kg
When operating a forklift, what is the primary purpose of the horn?
B. To alert pedestrians
D. Both A and B
A. To signal other operators
C. To indicate a malfunction
If a forklift operator is found to be under the influence of alcohol, what is the likely consequence?
C. Immediate termination
B. Suspension
A. A warning
D. No action taken
A forklift is rated for 2,000 kg at a 600 mm load center. What is its capacity at a 700 mm load center?
A. 1,800 kg
B. 1,600 kg
C. 1,500 kg
D. 2,000 kg
What is the primary purpose of the load backrest extension on a forklift?
A. To increase lifting speed
B. To prevent loads from falling backward
C. To improve visibility
D. To reduce noise
If a forklift operator is found operating without a valid certification, what is the likely consequence?
D. No action taken
C. Retraining required
B. Immediate suspension
A. A warning
The rear wheels begin to lift when raising a 2,800 kg load. What is the likely cause?
A. Tires are underinflated
B. Load center is beyond safe limit
C. Mast is too far back
D. Forks are too wide
You need to convert a load of 4,400 lbs into kilograms. What's the weight?
(a)
A ramp rises 2.4 m over 20 m horizontal. What is the angle of incline?
(don't use ° to answer)
(a)
You're using a side-shift attachment that weighs 250 kg. Rated capacity is 2,500 kg. What is your new capacity (assuming attachment offset reduces capacity by 10%)?
(a)
You’re lifting a load on a 14% incline. What trigonometric function helps determine effective force along the incline?
A. Cosine
B. Sine
C. Tangent
D. Cotangent
A forklift has a 2.5 m wheelbase. If the CG moves 0.6 m forward,
what percentage of the triangle’s base is exceeded? (use % to answer)
(a)
You're traveling with a 2,700 kg load at 10 km/h. Braking distance doubles when the speed halves.
A 1,200 mm-long load is placed with the CG at 800 mm. Rated CG is 500 mm.
What capacity loss is approximately? (use % to answer)
(a)
What is the primary function of the forklift's forks?
C. To provide stability
B. To steer the forklift
A. To lift and carry loads
D. To increase speed
When should a forklift operator perform a pre-operation inspection?
D. Only after an accident
B. At the beginning of each shift
A. Only when the forklift is new
C. Once a week
You're lifting a wide load where CG is 750 mm from forks. Rated capacity is 4,000 kg @ 500 mm.
What safe capacity is now?
(This question contains 10 points, be careful while answering)
(a)
A rectangular box is 1.2 m long and placed on a forklift so that 0.2 m of the load hangs past the fork tips. Forks are 1 m long. The load weighs 2,400 kg.
The forklift is rated 3,000 kg @ 500 mm.
What is the new load center?
(This question contains 10 points, be careful while answering)
(a)
/
/|
/ | Rise = 2 m
/ |
/ (a) |
Run = 10 m
A forklift is carrying a 2,000 kg load up a 10-meter ramp that rises 2 meters vertically. The incline forms a triangle.
What is the angle of the slope approximately? (don't answer with °)
(This question contains 10 points, be careful while answering)
You're using a fork positioner attachment that weighs 400 kg. Your forklift’s original capacity is 4,000 kg @ 500 mm.
The attachment shifts CG by +100 mm. What is the approximate new capacity?
(This question contains 10 points, be careful while answering)
(a)
A heavy load is tilted forward, shifting the CG outside the triangle's front edge.
What is the likely result?
(This question contains 10 points, be careful while answering)
A. The rear wheels lift slightly
B. Forklift drives faster
C. The load drops backward
B. The forklift tips forward
