You are about to use a tool and forgot to bring goggles with you. What do you do?

You see someone using a tool incorrectly. What do you NOT do?

Someone is right next to you while you are using a tool. What do you do?

You notice a piece of wood on the floor. What do you do? (Best answer)

You just finished painting your project and now you are waiting for the paint to dry. One way you can keep yourself occupied is to see how flat you can make a pencil by crushing it in the vise.

You notice there is water on the floor by the sink. Concerned that someone may slip and fall, you can either clean it up yourself or notify the teacher of the unsafe condition.

You are putting your project pieces together using a hammer and nails. Since you are not using the machines you do not have to wear safety goggles.

Before you start working you remove your glasses to put on safety goggles. You need your glasses to see properly at all times. In this situation you should put your safety goggles over your glasses.

A student doesn't follow the safety rules and doesn't think he will get hurt in Tech class. In this situation the student has a poor attitude about safety, which will cause more accidents.

You are cutting a piece of wood with a saw and the cleanup bell rings. You want to finish the cut so you don't fall behind on your project. In this situation you should press the wood harder against the blade to make the saw cut faster.

You notice a classmate is not adjusting the safety device on a tool correctly. In this situation you should either demonstrate to the student the correct way to adjust the safety device or notify the teacher of the situation.

Your friend playfully taps you on the shoulder and runs away. You start to chase him and the teacher sees both of you running. In this situation the student should not chase his friend since running is not allowed in class and you are responsible for your own actions even though your friend started it.

You are having a conversation with your friend while the teacher is demonstrating how to use a new tool. It is time to use the tool and you are unsure what to do. In this situation you should use the tool anyway to figure out how to use it on your own.

You are standing near the tool cabinet when your friend asks you to get her a hammer. You make sure no one is near and you gently toss the hammer to your friend. In this situation it is ok to throw a tool since you made sure no one was near and you were helping a friend.

Your cleanup job is to sweep the tables. All the dustpans and hand brooms are being used. Since you do not want to get in trouble for not doing your cleanup job, you should use your hand to clean the table.

You were absent on a day when the teacher demonstrated a new tool. It is time to use the tool for your project. In this situation you should not attempt to use the tool on your own but instead ask the teacher how to use it

What does a cut line look like?

You are the next person on line to use a tool. You notice that the line is long so you step right next to the operator so you can get to the tool quicker when it is your turn. In this situation it is all right to have more than one person in front of the tool.

Use the image below to answer this question. What type of line is this?

What does a finish line look like?

When completing a safety check, what do you NOT do?

You walk over to a tool to cut out your project, realize you forgot your safety goggles and don't want to walk back to get them. In this situation it is OK to cut your wood without your safety goggles as long as you turn your head away from the tool.

Use the image below to answer this question. What type of line is this?

You are finished cutting out your project on a tool and turning it off. You notice there are people behind you waiting to use the tool . In this situation it is all right to leave the scrap wood on the tool's table in case the next person needs to use it as a push stick.

Last period your friend plays a joke on you. While in Tech class you notice an opportunity to get back at them. You plan to take the piece of material that was just cut and hide it on them so they become frustrated and upset. Since you are not actually hurting your friend, it is ok to play this kind of trick in Tech class.

While working with a tool your friend starts asking you questions about last night's math homework. In this situation you should ignore your friend and not respond so you do not lose your focus on the tool.

While working with a tool, you start thinking about what you are going to be doing after school. After a moment you regain your focus and continue working with the tool. In this situation it is all right to let your mind wander as long as you regain your focus afterwards.

When done with the push stick, where should it be stored?

With all hand positions, what is being used to move the board into the blade?

Use the image below to answer this question. What is the name of this hand position?

Use the image below to answer this question. What is the name of this hand position?

Use the image below to answer this question. What is the name of this hand position?

Use the image below to answer this question. When would you use the hand position below?

Use the image below to answer this question. When would you use the hand position below?

Use the image below to answer this question. When would you use the hand position below?

Use the image below to answer this question. Why is this hand position awkward?

For a safety check you need to pull up your hair. Which hair style is not acceptable for a safety check

Check all that apply. When doing a safety check and you are reviewing your clothing, what do you need to be worried about?

The shoes you wear in the shop need to have two qualities. What are those qualities? Check off all that apply.

When do goggles need to be worn in the shop?

Which part of the safety check did this person not follow?

Which part of the safety check did this person not follow?

Which part of the safety check did this person not follow?

What should you do if you notice a tool is damaged before using it?

When is it acceptable to distract someone who is operating a machine in the shop?

After finishing your work, what is the correct way to leave your workspace?