NEW
Font size
WorksheetsAuto Collision Repair
Total questions: 36
Worksheet time: 15mins
What grit of sandpaper is used to first sand cured body filler?
40 grit
80 grit
180 grit
220grit
All of the following are vehicle safety systems EXCEPT:
brakes
steering
heating
restraint
Where can a technician find the right lifting and jacking points on a vehicle?
jacking label
lifting label
body repair manual
vehicle service manual
On a sheet of metal a straight file is used to:
flatten metal
find high and low spots
prepare the area for filler
sand the area
Metal surface irregularities can be eliminated by:
welding
grinding
picking and filing
brazing
Technician A says rough filler takes extra time to sand. Technician B says filler should be applied thick on the 1st coat. Who is correct ?
Technician A
Technician B
Both A and B
Neither A nor B
The % of hardener added to body filer is about ?
20%
5%
10%
15%
How many layers of fiberglass mat are used on the back of a cracked SMC (sheet molded compound)repair ?
1 layer
2 layer
3 layer
4 layer
Paint needs removed from a panel Technician A says use a DA.Technician B says a grinder. Who is correct?
Technician A
Technician B
Both A and B
Neither A nor B
Technician A says to clean all vehicles with wax/grease remover. Technician B says only if road tar is visible. Who is correct ?
Technician A
Technician B
Both A and B
Neither A nor B
What grit of grinding disc should be used to remove paint and surface rust?
24 grit
36 grit
40 grit
80 grit
Cold shrinking metal uses :
oxyacetylene torch
Mig welder
chisel
sharp pick hammer
Technician A says the estimate lists parts to replace.Technician B says estimate list parts to be repaired. Who is right ?
Technician A
Technician B
Both A and B
Neither A nor B
In a front end collision the right doors on a 4 door car need aligned.Technician A says to adjust front door 1st. Technician B says to adjust rear door 1st. Who's right?
Technician A
Technician B
Both A and B
Neither A nor B
Interior trim fastners need removed.Technician A says check estimating guide.Technician B says check body repair manual or Alldata. Who is right?
Technician A
Technician B
Both A and B
Neither A nor B
Hood must be slammed to latch.Technician A says raise the latch.Technician B says lower latch. Who is right?
Technician A
Technician B
Both A and B
Neither A nor B
A fender needs replaced.Technician A says you need to remove the battery to access bolts.Technician B says the marker light needs removed. Who is right?
Technician A
Technician B
Both A and B
Neither A nor B
Technician A says replacement panels can be visibly aligned.Technician B says measurements should be taken before fitting parts. Who is right?
Technician A
Technician B
Both A and B
Neither A nor B
Tape stripes are removed with a:
grinder
DA (dual action sander)
putty knife
razor blade
All of the following methods are used to attach moldings except:
clips
screws
welding
adhesives
Rough out means to:
prepare area for body filler
remove a damaged panel
sand an area for paint adhesion
restore the damage to its regular contour
When compared to normal metal,stretched metal is:
thicker
thinner
smaller
shorter
Some guide coat remains after sanding.Areas with guide coat indicate:
low spots
high spots
wet spots
soft spots
Filler has been applied over paint.Tech A says its ok.Tech B says paint needs to be removed and refilled .
Tech A
Tech B
Both A and B
Neither A nor B
All the following surfaces can be used to mix body filler except :
cardboard
glass
metal
plastic
Cold shrinking involves:
reducing the surface area of the stretched metal
increasing the surface area of the stretched metal
spreading out the surface area of the stretched metal
thinning the area of the stretched metal
When filing,the file will not contact:
high spots
low spots
ridges
buckles
What tool is used to shape partially cured body filler?
long block
air file
cheese grader
metal file
when removing surface irregularities by picking & filing,what tool is used to raise low spots?
ball peen hammer
file
pick hammer
slide hammer
Tech A says bare metal should be cleaned with wax/grease remover.Tech B says it is not necessary. Who is correct ?
Tech A
Tech B
Both A and B
Neither A nor B
Technician A says all door skins are welded onto door frames.Technician B says intrusion beams are found on passenger car doors. Who is correct ?
Tech A
Tech B
Both A and B
Neither A nor B
When replacing a Quarter panel.Tech A says check with manufacturer for sectioning procedure.Tech B says section where there is space. Who is right ?
Tech A
Tech B
Both A and B
Neither A nor B
Gap between hood and fender should be:
2mm
4mm
6mm
7mm
anti-corrosive is sprayed inside a repaired panel.Tech A says its wax based Tech B says its water based.Who is correct?
Tech A
Tech B
Both A and B
Neither A nor B
Tech A says moldings may be installed with adhesive.Tech B says moldings maybe installed with clips. Who is correct ?
Tech A
Tech B
Both A and B
Neither A nor B
All of the following are used to retain interior trim EXCEPT:
snap-in clips
welding
push pins
small screws
