NEW
Font size
WorksheetsMan/Tran OSHA - complete
Total questions: 50
Worksheet time: 24mins
It is the employer’s responsibility to ensure that their employees are medically fit enough to use a respirator.
True
False
A tagout device must state the following:
See your supervisor before operating this machine
Only operate this machine after checking that it is clear of persons and repair equipment
Do not operate this machine or move the energy isolating devices from the "safe" or "off" position
Who is responsible for hand and power tool safety?
The employer
The employee
OSHA
Both a and b
Ladders can be tied together to make longer sections, provided steel wire and metal clamps are used
True
False
Which of the following is NOT a safe practice when working with power tools?
Yanking the hose or the cord to disconnect it from the receptacle
Securing work with a vice or clamps, keeping both hands free to use the tool
Keeping hoses and cords away from oil, heat, and sharp edges
All slips, trips, and falls should be reported even when no one is hurt.
True
False
Who may remove the lock from the machine?
An affected employee
The employee who sees the person close the lock
The person who closed the lock
The employer
Which of the following can cause slips, trips, and falls?
Distraction
Poor vision
Cautiousness
Both a and b
Even when there are no signs of a fire, you should respond to every fire alarm as if it were real.
True
False
Electric tools should not be used in damp or wet locations.
True
False
When must your employer retrain you?
Whenever you will be working with a new chemical that has hazards on which you haven’t already received training
Every 12 months
Every 6 months
Whenever a chemical is delivered to your facility
You are required to ask a victim’s permission to perform first aid.
True
False
A toe board is required around a floor opening to...
Prevent materials from falling through the opening
Assist in maintaining overall cleanliness
Increase the strength of railings
Protect workers who aren’t wearing protective footwear
Machine guards should be fitted to protect the operator and others nearby from…
In running nip points
Flying chips & sparks
Points of operation
Rotating parts
All of the above
Your employer must retrain you when there is a change in…
Work assignments
Process or machinery, either of which poses a new hazard
Energy control procedures
All of the above
Which of the following should you do first when your co-worker has suffered a severe electrical shock?
(Hint: They're no longer being shocked and are unconscious on the floor but are clearly hurt)
Move the victim away from the electrical source with a help of a non-conducting object
Check the victim’s breathing and pulse. Begin CPR if necessary
Lay the victim down with his/her head lower than the rest of the body
Call 911 or bring in an emergency medical team
What does the acronym SDS stand for?
Safety Data Sheet
Safety Description Sheet
Security Data Sheet
A portable fire extinguisher should only be used by trained employees.
True
False
The maintenance department in your plant found that Lysol® Toilet Bowl Cleaner does a great job for polishing the outside of storage tanks. Your supervisor says that there is no need to train you because the material is a common consumer cleaning product and you will be using it for its intended use. Is this the proper procedure?
Yes
No
What action(s) should be taken to minimize slips, trips, and falls in the workplace?
Always be aware of your surroundings
Wear slip-resistant footwear
Use handrails when available
all of the above
How can toxic chemicals enter your body?
Ingestion
Absorption
Inhalation
All of the above
Which of the following is the acronym describing the correct sequence of using a fire extinguisher?
PULL
PASS
PUSH
Which of the following is the most serious burn that destroys skin and underlying tissue?
3rd degree burns
2nd degree burns
First degree burns
While setting up a ladder against a wall or other support, its base should be moved _____ inches away from the wall for every foot of the ladder’s height.
2
3
4
5
Which of the following types of gloves should you wear when working with chemicals?
Leather gloves
Fabric gloves
Butyl rubber gloves
Gloves aren't necessary
When must your employer provide you information and training on hazardous chemicals?
Thirty days after your initial assignment
Never
The week after initial assignment
At the time of your initial assignment
Which of the following is a bad example of proper workplace cleanliness?
Keeping equipment on stairways where they can be easily located.
Providing warning signs for wet floors.
Maintaining drainage, false floors, mats, platforms or dry standing places where there are wet or oily processes.
Cleaning and organizing passageways, service rooms, storerooms and places of employment.
If you want more information about the hazards of a chemical with which you are working, your employer must provide you a SDS -
At the end of your shift
Immediately
Within 4 hours of your request
The next time you come to work
The maximum permitted height for a step ladder is...
15 feet
20 feet
12 feet
8 feet
Which of the following compromises the effectiveness of the respirator’s seal?
Beards
Mustaches
Sideburns
Stubble
All of the above
The Hazard Communication Standard is based SOLELY (only) on the concept that employees need to know about the hazards to which they are exposed.
True
False
Where should you aim a fire extinguisher nozzle when putting out a fire?
Away from the fire
At the center of the fire
At the top of the fire
At the base of the fire
While tightening a nut with a wrench...
The wrench should be pulled toward you
The wrench should be pushed away from you
Which of these symptoms suggests that your respirator may be ineffective?
Shortness of breath
Dizziness
Coughing
All of the above
Arrange in order the correct the steps to take when someone splashes a chemical into the eye.
1.Call a doctor
2.Take out any contact lenses
3.Flush the eyes with plenty of water
4.Wash your hands with soap and water
2,3,4,1
3,4,2,1
1,3,4,2
4,2,3,1
Which of the following is a warning sign that your workplace may be too noisy?
You hear a humming or ringing in your ears when you leave your workplace
You constantly pull your ears
You have to shout to a person who’s an arm’s length away in order to be heard.
Both a and c
When someone swallows a chemical, immediately have the person drink water and then induce vomiting.
True
False
It is okay to remove safeguards if you’re an experienced hand and power tool operator.
True
False
Who is responsible for maintaining PPE (personal protective equipment)?
Your employer
Yourself
Your co-worker
A and B
Which of the following is the leading cause for falling fatalities?
tripping over objects
stairs and steps
slippery tiles
ladders
Which of the following information must a label of a container holding a hazardous chemical include?
Identity of the hazardous chemical(s)
Appropriate hazard warnings
Name and address of the chemical manufacturer or importer
All of the above
When should employees be informed of the fire hazards to which they are exposed at work?
Within 30 days of the initial assignment
Within two days of the initial assignment
Upon the initial assignment
Within 90 days of the initial assignment
The primary function of a fire door is to stop the fire from spreading.
True
False
What type of protection is needed when you are exposed to hazards from flying particles?
Eye protection
Face protection
Head protection
Both a and b
What causes a chemical burn?
hot metal
corrosive
A torch
gasoline
Eye protection is required for which of the following hazards?
Flying particles
Molten metal
Liquid chemicals, acids or caustic liquids
All of the above
Respirators DO NOT protect workers against…
Fog, mist, and smoke
Paint fumes
Harmful dusts
Falls
Continuous exposure to noise levels at ____ decibels (dB) or above can cause hearing loss.
80
75
85
90
How high is a standard railing?
38 inches
42 inches
24 inches
high enough to prevent someone from falling
Below is a list of fire extinguisher types matched with surfaces on which they can be used. Which is the incorrect option?
Class D - Combustible metals such as magnesium, potassium, titanium, and sodium
Class B - Plastics, oils, grease, gasoline, solvents, and other flammable liquids
Class C - Wiring, fuse boxes, electrical equipment, and computers
Class A - Cloth, wood, paper, and rubber
