Ballcocks in water closet tanks shall be installed so that the critical level of the water inlet is above the full opening of the overflow pipe at least _____.

Minimum height of the atmospheric vacuum breaker critical level above all downstream piping for lawn sprinkler system: _____

After allowing for friction and other pressure losses, the residual water pressure shall be at least _____.

The quantity of water required to be supplied to every plumbing fixture shall be represented by _____.

Solder and fluxes used in piping systems conveying potable water are prohibited when the lead content exceeds _____ percent.

The maximum trap loading for a 3 inch trap is _____.

The clearance required in front of a 2 inch cleanout shall not be less than _____.

The total number of fixture units at “A” is _____.

Which of the following is an approved method of protecting the water supply for a chemical dispenser?

The maximum fixture unit loading allowed on a 2 inch waste stack is _____.

The minimum size trap and trap arm for a bathtub is _____.

Of those listed the acceptable fitting for connecting a horizontal drain line with another horizontal drain line is a _____.

The total number of fixture units at “A” is _____.

Of those listed, the appropriate fitting at “E” would be a _____.

Ballcocks in water closet tanks shall be installed so that the critical level of the water inlet is above the full opening of the overflow pipe at least _____.

The primary reason for installing backflow prevention assemblies is to _____.

Minimum height of the atmospheric vacuum breaker critical level above all downstream piping for lawn sprinkler system: _____

Each outlet on a nonpotable water system that is used for special purposes shall be posted _____.

Copper water tube Type “M” may be installed within a building _____.

Water piping may be installed in the same trench with less than 12 inches of separation from a building sewer constructed of _____.

Hard-drawn copper tubing, marked with a blue stripe, is referred to as _____.

The color stripe on Type “K” hard-drawn copper tubing is _____.

Except as required in Section 601.3.3, nonpotable water systems shall have a _____ with black uppercase lettering, with the words “CAUTION: NONPOTABLE WATER, DO NOT DRINK.”

The minimum wall thickness for threaded plastic pipe (not molded fittings) shall be _____.

Three-inch horizontal drainage piping shall have a grade or slope of not less than _____.

The minimum size drain line for a wall-hung urinal is _____ inches.

The total number of fixture units at “A” is _____.

The minimum size pipe at “B” is _____.

A straight run of building sewer will require cleanouts at intervals not to exceed _____.

All indirect waste piping that requires an airgap shall discharge into the building drainage system through _____.

A standpipe for a clothes washer shall have a minimum and maximum length of _____.

The minimum size condensate waste pipe from a 12-ton refrigeration unit is _____.

12. Each vent pipe or stack shalI extend through its flashing and shall terminate vertically above the roof at least _____.

25. A drainage stack extends 14 stories above the building drain and is served by a parallel vent stack. A relief yoke vent connection between the vent stack and the drainage stack is required at _____.

50. Horizontal wet venting _____.

1. Vent pipes protect fixture traps against _____.

5. The combination of vent pipes that will provide sufficient aggregate cross-sectional vent area for required a 4-inch house sewer is _____.

8. The distance “X” in the sketch above shall be at Ieast _____.

14. Horizontal termination of vents from any openable window, door opening, air intake or vent shaft shall be not less than _____.

20. The pipe size for the common vent serving lavatories installed back-to-back shall be not less than _____ inch(es).

Of those listed, the test medium for a gas piping pressure test shall be _____.

When a flanged joint is separated, the gasket shall be _____.

Minimum height of the atmospheric vacuum breaker critical level above the overflow rim of a tank, vat or swimming pool: _____

After allowing for friction and other pressure losses, the residual water pressure shall be at least _____.

Water piping may be installed in the same trench with less than 12 inches of separation from a building sewer constructed of _____.

The type of valve required on a building supply to any building is a _____.

Other than systems sized by the use of Table 610.4, the maximum velocity of a cold water system containing copper and copper alloy tube and fittings shall be limited to _____.

Discharge piping serving a pressure-relief shall be provided with a _____.

Whenever fixtures and/or fixture fittings are installed that require a residual water pressure higher than 15 pounds per square inch _____.

A _____ joint is an example of a mechanical joint for CPVC Plastic pipe.

The maximum discharge capacity for intermittent flow only, in gallons per minute, for one fixture unit is equal to _____.

A straight run of building sewer will require cleanouts at intervals not to exceed _____.

When discharged into the drainage system, condensate shall drain by means of a(an) _____.

26. The fitting that is required for making the yoke vent intersection with the drainage stack is a _____.

38. The sketch represents _____.

42. The type of fitting acceptable at “D” is a _____.

47. The minimum size (diameter) for vent piping “B” shall be approximately equal to _____.

45. The minimum size (diameter) of the tailpiece for the floor drain served by “A” is _____.

1. The _____ may require the submission of plans, specifications, drawings, and such other information, prior to the commencement of work regulated by this code.

The _____ shall be responsible for maintenance of plumbing systems.

1. Parts of the plumbing system of a building or part thereof that is moved from one foundation to another,

or from one location to another, shall be in accordance with the provisions of _____ for new installations.

To obtain a permit, the applicant shall first file _____ therefore in writing on a form furnished by the Authority Having Jurisdiction for that purpose.

This code is an ordinance to provide _____ for the protection of the public health, safety, and welfare.

1. Temporary connection of the plumbing equipment to the source of energy or fuel for the purpose of testing _____.

A room equipped with a shower, bathtub or combination bath/shower is a _____.

The length along the centerline of the pipe and fittings is the _____.

The vertical depth of a trap seal is measured from _____.

select the word or term that fits the sketch.

select the word or term that fits the sketch.

select the word or term that fits the sketch.

The lowest portion of the inside of a horizontal pipe is called the _____.