One of the leading causes of disability for UBC members is back injuries.

The best method for preserving a chalk line is to spray it with clear lacquer at intermittent sections.

The most economical way to maintain a sharp utility knife is to carry around a package of replacement blades.

Three points of contact refers to having two hands and one foot or two feet and one hand in full contact with a ladder while ascending and descending

Cranes are only useful when moving loads vertically

The floor plan is usually the starting point for construction layout.

Due to the irregular surface of corrugated steel roof decks, the top track is more difficult to install and care must be taken to ensure that all points are transferred accurately.

Detail views include precise information about construction that will not fit in other views drawn to a smaller scale.

The most common steel components used in framing a wall are _____.

The most productive method of tying ceiling hanger wire to an eye-lag

is with _____.

_______________ are all examples of existing hazards.

A square is _________.

A _____ is an interior layout laser system that communicates with a tablet controller via Wi-Fi

____________ are structural framing components that are horizontally built-up to span openings and carry loads to adjacent vertical framing components

The measurement from the upper surface of the finish flooring to the elevation of a feature being dimensioned is referred to as _________.

Control lines are commonly oriented off of _________.

The formula used to calculate from the corner of a square to the corner of an octagon is ________.

A _______ is needed before a jig can be fabricated. 

The floating framing member placed into the track at a corner or intersection to allow the main wall finished to be installed first without interruptions is known as a(n) _____ stud.

A ________ header requires two pieces of track and two pieces of stud.

Another possible combination used to create a 3-4-5 square corner is _____.

When using the diagonal of a square method to lay out an octagon, the remaining length of the diagonal after subtracting the side of the square is the dimension of the ________.

Tabbed or overlapped intersections will be used on the _____ track of _____ walls.

Two considerations when marking stud length are ______________.

The method for laying out metal stud partitions that is recommended as best practice because of its efficiency is the_______________.

When constructing a box corner, the long edge of the main wall track should be installed on layout with the end of the track held _____ back from the corner.

For fire-rated columns, the drywall corners are alternated as the panels are installed, creating a _____ pattern.

Resilient channel is a type of furring used to_______.

The specified size of acoustical sealant beads is______.

Shaft walls offer sound transmission class ratings up to ______.

An evacuation ________ is a posted diagram that shows how to quickly exit a building or work site in case of a fire or other emergency

When considering fastening systems, the __________ propellant fastening system is the safest and most environmentally friendly.

Environmental hazards that may create potential dangers include noise ,fumes, and ________ materials.

A ________ is formed when separate pieces of material are fused together through the application of heat.

When choosing between a 20-gauge DW metal component and a 20-gauge STR component, the STR component is thicker and stronger.

A(n) _______ test may not detect all defects in a grinding wheel, so a careful visual inspection is also needed.

The most common color-coded powder-actuated fastening loads are green, yellow, and ___________.

To avoid musculoskeletal injuries, a lifting or _________ device should be used whenever possible.

A(n) _______ clip is needed when structural steel is used for hanger wire anchorage.

A(n) ____________ is a heavy-duty, variable-speed power tool commonly used in metal framing for concrete drilling and corrective chiseling.

_________ and shears are powered hand tools designed to cut sheet metal studs, track, or metal ceiling tile.

The preferred type of outside corner is a(n) _______ corner.

The temporary shipping bars on a welded metal door frame should be removed and replaced with a door ________ to maintain the opening size during installation.

When using a table saw to cut the kerf for wood backing, a dado _______ is preferred.

A(n) ________ is a pattern used for repeating assembly of a standardized unit.