NEW
Font size
WorksheetsCC 101
Total questions: 41
Worksheet time: 21mins
Safety is a ______
way of making a task more time consuming.
unnecessary consideration if you know what your doing.
learned behavior.
of get getting out of work.
Information markings or signs provide general information. These signs are what color?
Red
Yellow
Green
Blue
All on-the-job incidents and accidents, no matter how minor, must be _____.
the employees fault
the companies fault
reported to the supervisor
reported if resulting in a death
What percentage of all accidental deaths in the construction industry are caused by slips, trips, and falls on WALKING and WORKING surfaces?
0.05
0.1
0.15
0.20
Poor lighting, excessive noise, and inadequate guards for moving parts are all examples of _____.
unsafe acts
unavoidable risk
unsafe conditions
acceptable risk
Risk is _______.
known as as the measure of probability, consequences, and exposure to an event.
known as something to avoid at all cost.
known as a evaluation process.
known as another way to describe a hazard.
A job safety analysis (JSA) is use to do what?
Break a task down into individual parts to analyze for potential hazards
Eliminate all hazards through studying chemicals
Review the causes of a injury or accident
Calculate the cost required in order to work safely
SDS must be kept where?
At home.
Readily available on the job site.
In the supervisors truck.
At the company head quarters.
To prevent falls from occurring due to an opening in a wall or floor, what preventive measure(s) must be implemented?
The opening must be repaired to continue work.
The opening must be guarded or covered.
The opening must be marked.
It is fine as long as everyone know about it.
What type person should inspect a PFAS monthly?
Competent person
Supervisor
Safety Supervisor
Manager
A non-shock absorbing lanyard should only be used for
fall arresting
positioning
descending
ascending
Where should the D-Ring or support point on a safety harness be placed?
The base of the neck.
Around the thighs.
Around the waist.
Between the shoulder blades.
Vertical lifelines must have a minimum breaking strength of how many pounds?
2,000lbs
3,000lbs
4,000lbs
5,000lbs
Horizontal lifelines are rated for
5,000 lbs
2.5 tons
a maximum number of workers
any number of workers
The distance between the foot of a ladder and the base of the structure it is leaning against must be _____ of the distance between the ground and the point where the ladder touches the structure.
1/8
1/4
1/2
3/4
How far should the top of an extension ladder extend above the point where the ladder touches the roof or platform it is leaning against?
1 feet
2 feet
3 feet
4 feet
The highest safe standing level extension ladders is _____.
2 rungs from the top
3 rungs from the top
4 rungs from the top
5 rungs from the top
A yellow tag on a scaffold indicates the scaffold
is safe to use
is unsafe to use
does not meet all safety standards
Daily inspections of an excavation must be performed by who?
Foreman
Engineer
Qualified Person
Competent Person
In the ABSENCE of other information, ALL soil in an excavation should be treated as if it is ______.
Type A
Type B
Type C
Solid Rock
Benching systems are prohibited in ______.
Type A soils
Type B soils
Type C soils
Solid Rock
Machine guards should always be in place and never removed. These machine guards protect workers from _____.
flammable objects
electrocution
rotating parts
chemical hazards
A polarized electrical receptacle is used for ______.
three wire power plugs
all power tools.
double insulated power tools.
current limiting power tools only.
Which of the following is the CORRECT process for a lockout/tagout situation?
Only one lock should ever be applied regardless of the number of people working.
The person who placed the first lock or tag is authorized to remove any other locks or tags.
Multiple lockout devices are required when more than one person is working.
A supervisor must be present when a lock or tag is placed.
In a lockout/tagout situation, a personal lock and tag MUST be removed by who?
A qualified person
A competent person
A safety supervisor
The person who applied them
You should use hearing protection if you must raise your voice to be heard by someone who is ______.
Less than 2ft away
More than 2ft away
3-4ft away
5-6ft away
OSHA's 29 CFR, Part 1926.1153 is known on work sites as the ______.
Silica Standard
Fall Protection Amendment
Workers Right to Unions
HAZCOM Standard
Vacuums and Respirators used to capture silica dust must be equipped with _____.
Bio-Hazard filters
Asbestos filters
UL- approved filters
HEPA filters
If you suspect asbestos may be present where you are working, you MUST ______.
put on the proper PPE before disturbing it.
report it to a supervisor and avoid disturbing it.
remove the asbestos as quickly as possible.
call OSHA.
What type of respirator would be used when exposed to dust or solid particles that might be inhaled?
Half mask or mouthpiece with a mechanical filter
SCBA
Full Facepiece Mask
Supplied air mask
Positive and Negative pressure fit checks should be performed on a respirator when?
The first time it is worn.
Once a week.
Once a month.
Every time it is worn.
One source of lead on some job sites is _____.
Water
Paint
Food
Blood
Hepatitis is a disease that can be transmitted through _____.
Blood
Water
Food
Eye Fluid
Out of the four answers, which one is considered to be life threatening?
Heat Exhaustion
Heat Stroke
Frostbite
Dehydration
When other works are working in nearby a welder or welding operation, the standard practice is to
weld with the least amount of gas as possible.
allow only one person to weld at a time.
make sure plenty of fire extinguishers are close by.
screen the work area with welding curtains.
What can occur if oxygen is mixed with oil or grease?
Nothing
It could explode
It could combust
It could release harmful fumes
If an ELECTRIC motor was on fire, what type of fire extinguisher would you use to extinguish the fire?
Type A
Type B
Type C
Type D
True or False? Combustible is when a fuel has a flash point above 100 degrees Fahrenheit.
TRUE
FALSE
True or False? Flammable is when a fuel has a flash point below 100 degrees Fahrenheit.
TRUE
FALSE
A permit-required confined space requires what type of permit before an employee can access the confined space?
Hot Work Permit
Excavation Permit
Entry Permit
Building Permit
When you stack materials, you should not stack materials beyond a
3:1 ratio
4:1 ratio
5:1 ratio
10:1 ratio
