Font size
WorksheetsSafety and Equipment Quiz
Total questions: 50
Worksheet time: 25mins
Quiz: How many classes are there of rubber protective equipment?
6
4
3
5
Quiz: Osha requires that live line tools be tested and cleaned (a) every years?
3
6 months
Quiz: The maximum AC voltage for Class 2 rubber gloves is?
1,700
17,000
33,000
14,400
Quiz: __________ is bonded to the inner wall of a standard hot stick to provide mechanical and electrical strength?
Fiberglass
Plastic
Rubber
Wood
Proper testing, inspection & maintenance of tools/equipment is to minimize risk to the worker.
True
False
Quiz: While working on energized lines/equipment, electrical contact accidents only occur when...
Hot sticks have not been tested
Gloves have been tested
Second point of contact exists
Rubber good type is ozone resistant
A job briefing or tailboard should contain which of the following according to OSHA?
Energy Source Controls
Hazards Associated with Job
Special Precautions
All the above
We should test our rubber blankets every 6 months just like our rubber gloves?
True
False
The person in charge should create an open environment for all to speak when performing a tailboard?
True
False
Quiz: When would you use rubber gloves to connect and disconnect load?
When the Foreman says it is OK
When you have the circuit on
Never
Use a live line tool when you are using Class 4 gloves
Rubber Blankets should be stored flat or rolled, never folded?
True
False
Quiz: What is the major cause of most accidents?
Unsafe Conditions
Unsafe Equipment
Unsafe Behaviors
Faulty Inspections
When is a job briefing required by OSHA?
Every Monday to start the week
Once a month
At the end of the job
Before starting the job
In the majority of electrical contacts the employee violated the?
Minimum Arc Fault Rating
Minimum Approach Distance
FR Rating
Maximum Available Fault Current
Quiz: __________ is a hotstick with a hollow core?
Telescoping Stick
Insulated Stick
Solid Stick
Extension Stick
Hotsticks that are manufactured today use which material?
Wood and Resin
Fiberglass reinforced plastic
Fiberglass wrapped around wood
Thermoplastics
Link sticks are used to provide insulation for ropes, blocks, and strap hoists.
True
False
When should we test our plastic cover up?
Before in service and once a year
Before in service and twice a year
When we are uncertain about condition
Every 3 years
There are (a) classes of Rubber Gloves?
4
7
Which of the following elements will reduce risk when performing live-linework?
Well Trained Employees
PPE is Properly Utilized
Proper Methods are Followed
All the Above
Rubber gloves should be used with the proper leather protectors.
True
False
An example of plastic cover up would be?
Clothes Pins
Hoist Handles
Blankets
Pole Wrap
When connecting a load pick up jumper the lineman should?
Connect the energized side first
Make load with the mechanical jumper
Fuzz the line to make sure it is not connected
Connect the de-energized side first
Pole safety has both and costs?
Indirect & Non-Substantial
Layoffs & Unproductive Time
Personal tragedy, Nothing to lose & Immaturity are all attitude indicators that can lead to accidents.
True
False
There are subjects required by OSHA that must be covered in a JHA or Tailboard.
6
3
8
A thorough job briefing can make the work environment both safe and productive?
True
False
Before starting a hot stick job it is recommended that the lineworker?
Lightly wipe all sticks to remove dirt and debris
Go to work!
Wet test all sticks
Apply glove dust
to exposure is most common when working on single phase lines.
Secondary to Ground
Primary to Secondary
What should every pair of rubber gloves and sleeves have present?
Test Date and Voltage Rating
Test Date and Ampacity
Voltage Rating and Ampacity
Ampacity and Corona Value
__________ dictate which voltages can and cannot be gloved.
State Laws & Utility Companies
Federal Regulations
Local Ordinances
Industry Standards
A live line tool should always be used to make and break load?
True
False
Quiz 00 class rubber gloves have a max AC voltage of?
100
50
500
1000
Quiz FR clothing shall be worn at all times while performing rubber gloving?
True
False
Quiz Class 2 rubber gloves have a Max use AC voltage rating of?
20,000
26,500
17,000
30,000
Quiz OSHA requires that at least (a) employees be present when working energized lines over 600 volts?
2
4
1
Before installing temporary jumpers we should check?
Available fault current
The size of the conductor
The downstream protection ampacity
Amperage on the line
Quiz Elements of an effective job briefing are?
Open Communication
OSHA requirements are met
Everyone understands the task at hand
All the above
OSHA prohibits FR clothing being made of acetate, nylon, polyester and rayon?
True
False
Quiz Live line tools suffer more abuse in storage and transportation than on the job?
True
False
Quiz Hot sticks made from the newest materials might be wet tested at?
7,500 volts per foot for 1 minute
25,000 volts per foot for 1 minute
75,000 volts per foot for 1 minute
100,000 volts per foot for 1 minute
What considerations for altitude need to be taken when dealing with system voltages?
It allows you to rubber glove at higher elevations
It helps extinguish the arc in thin air
It increases the MAD to a safe distance due to elevation
You don't need to factor in elevation go to work!
Which of the following considerations do rubber gloving and hot sticking have in common?
Non reclose condition
Second point of contact
Conductor control
All of the above
When hot sticking it is important to use the entire length of the stick to help maintain?
Stick Integrity
Minimum Approach Distance (MAD)
Minimize Fault Current
Minimum Voltage Drop
Barehanding was introduced to the power industry in?
1959
2019
1988
1960
Type I rubber goods are non ozone resistant, while Type II rubber goods are ozone resistant?
True
False
is the most versatile and oldest method for working on energized lines?
Rubber Gloving
Hot Sticking
De-energizing
Barehanding
True or false: Class 3 rubber goods can be used on a 14,400/24,940 system when rubber gloving?
True
False
The distance required between the end of the leather protector and the end of the cuff on Class Three gloves is?
1 inch
3 cm
3 inches
2 inches
An air test can show the smallest damage to:
Rubber Sleeves
Rubber Blankets
Rubber Gloves
EH Boots
